All Dielectric Self-Supporting Cable

ADSS

All Dielectric Self-Supporting Cable

The structure of ADSS (single-sheath stranded type) is to place 250um optical fiber into a loose tube made of PBT, which is then filled with waterproof compound. The center of the cable core is a non-metallic central reinforcement made of fiber-reinforced composite (FRP). The loose tubes (and filler rope) are twisted around the central reinforcing core. The seam barrier in the relay core is filled with water-blocking filler, and a layer of waterproof tape is extruded outside the cable core. Rayon yarn is then used, followed by extruded polyethylene (PE) sheath into the cable. It is covered with a thin polyethylene (PE) inner sheath. After a stranded layer of aramid yarns is applied over the inner sheath as a strength member, the cable is completed with a PE or AT (anti-tracking) outer sheath.


Product Detail

FAQ

Product Tags

Product Video

Product Features

Can be installed without shutting off the power.

Resistant to high and low temperature cycles, resulting in anti-aging and a longer lifespan.

Lightweight and small diameter reduce the load caused by ice and wind, as well as the load on towers and backprops.

Large span lengths and the longest span is over 1000m.

Good performance in tensile strength and temperature.

Large number of fiber cores, lightweight, can be laid with the power line, saving resources.

Adopt high-tensile-strength aramid material to withstand strong tension and prevent wrinkles and punctures.

The design lifespan is over 30 years.

Optical Characteristics

Fiber Type Attenuation 1310nm MFD

(Mode Field Diameter)

Cable Cut-off Wavelength λcc(nm)
@1310nm(dB/KM) @1550nm(dB/KM)
G652D ≤0.36 ≤0.22 9.2±0.4 ≤1260
G657A1 ≤0.36 ≤0.22 9.2±0.4 ≤1260
G657A2 ≤0.36 ≤0.22 9.2±0.4 ≤1260
G655 ≤0.4 ≤0.23 (8.0-11)±0.7 ≤1450

Technical Parameters

Fiber Count Cable Diameter
(mm) ±0.5
Cable Weight
(kg/km)
100m Span
Tensile Strength (N)
Crush Resistance (N/100mm) Bending Radius
(mm)
Long Term Short Term Long Term Short Term Static Dynamic
2-12 9.8 80 1000 2500 300 1000 10D 20D
24 9.8 80 1000 2500 300 1000 10D 20D
36 9.8 80 1000 2500 300 1000 10D 20D
48 9.8 80 1000 2500 300 1000 10D 20D
72 10 80 1000 2500 300 1000 10D 20D
96 11.4 100 1000 2500 300 1000 10D 20D
144 14.2 150 1000 2500 300 1000 10D 20D

Application

Power Line, dielectric needed or large span communication line.

Laying Method

Self-supporting aerial.

Operating Temperature

Temperature Range
Transportation Installation Operation
   -40℃~+70℃    -5℃~+45℃    -40℃~+70℃

Standard

DL/T 788-2016

PACKING AND MARK

OYI cables are coiled on bakelite, wooden, or ironwood drums. During transportation, the right tools should be used to avoid damaging the package and to handle them with ease. Cables should be protected from moisture, kept away from high temperatures and fire sparks, protected from over-bending and crushing, and protected from mechanical stress and damage. It is not allowed to have two lengths of cable in one drum, and both ends should be sealed. The two ends should be packed inside the drum, and a reserve length of cable not less than 3 meters should be provided.

Loose Tube Non-metallic Heavy Type Rodent Protected

The color of cable markings is white. The printing shall be carried out at intervals of 1 meter on the outer sheath of the cable. The legend for the outer sheath marking can be changed according to the user's requests.

Test report and certification provided.

  • Products Recommended

    • OYI H Type Fast Connector

      OYI H Type Fast Connector

      Our fiber optic fast connector, the OYI H type, is designed for FTTH (Fiber to The Home), FTTX (Fiber to the X). It is a new generation of fiber connector used in assembly that provides open flow and precast types, meeting the optical and mechanical specifications of standard optical fiber connectors. It is designed for high quality and high efficiency during installation.
      Hot-melt quickly assembly connector is directly with a grinding of the ferrule connector directly with the falt cable 2*3.0MM /2*5.0MM/2*1.6MM, round cable 3.0MM,2.0MM,0.9MM, using a fusion splice, the splicing point inside the connector tail, the weld is no need for additional protection. It can improve the optical performance of the connector.

    • Central Loose Tube Stranded Figure 8 Self-supporting Cable

      Central Loose Tube Stranded Figure 8 Self-suppo...

      The fibers are positioned in a loose tube made of PBT. The tube is filled with a water-resistant filling compound. The tubes (and the fillers) are stranded around the strength member into a compact and circular core. Then, the core is wrapped with swelling tape longitudinally. After part of the cable, accompanied by the stranded wires as the supporting part, is completed, it is covered with a PE sheath to form a figure-8 structure.

    • ADSS Suspension Clamp Type B

      ADSS Suspension Clamp Type B

      The ADSS suspension unit is made of high tensile galvanized steel wire materials, which have higher corrosion resistance capability, thus extending the lifetime usage. The gentle rubber clamp pieces improve self-damping and reduce abrasion.

    • OYI-FOSC-M8

      OYI-FOSC-M8

      The OYI-FOSC-M8 dome fiber optic splice closure is used in aerial, wall-mounting, and underground applications for the straight-through and branching splice of the fiber cable. Dome splicing closures are excellent protection of fiber optic joints from outdoor environments such as UV, water, and weather, with leak-proof sealing and IP68 protection.

    • Air Blowing Mini Optical Fibre Cable

      Air Blowing Mini Optical Fibre Cable

      The optical fiber is placed inside a loose tube made of high-modulus hydrolyzable material. The tube is then filled with thixotropic, water-repellent fiber paste to form a loose tube of optical fiber. A plurality of fiber optic loose tubes, arranged according to color order requirements and possibly including filler parts, are formed around the central non-metallic reinforcement core to create the cable core via SZ stranding. The gap in the cable core is filled with dry, water-retaining material to block water. A layer of polyethylene (PE) sheath is then extruded.
      The optical cable is laid by air blowing microtube. First, the air blowing microtube is laid in the outer protection tube, and then the micro cable is laid in the intake air blowing microtube by air blowing. This laying method has a high fiber density, which greatly improves the utilization rate of the pipeline. It is also easy to expand the pipeline capacity and diverge the optical cable.

    • 10/100Base-TX Ethernet Port to 100Base-FX Fiber Port

      10/100Base-TX Ethernet Port to 100Base-FX Fiber...

      MC0101F fiber Ethernet media converter creates a cost-effective Ethernet to fiber link, transparently converting to/ from 10 Base-T or 100 Base-TX Ethernet signals and 100 Base-FX fiber optical signals to extend an Ethernet network connection over a multimode/single mode fiber backbone.
      MC0101F fiber Ethernet media converter supports maximum multimode fiber optic cable distance of 2km or a maximum single mode fiber optic cable distance of 120 km, providing a simple solution for connecting 10/100 Base-TX Ethernet networks to remote locations using SC/ST/FC/LC-terminated single mode/multimode fiber, while delivering solid network performance and scalability.
      Easy to set-up and install, this compact, value-conscious fast Ethernet media converter features autos witching MDI and MDI-X support on the RJ45 UTP connections as well as manual controls for UTP mode, speed, full and half duplex.

    If you're looking for a reliable, high-speed fibre optic cable solution, look no further than OYI. Contact us now to see how we can help you stay connected and take your business to the next level.

    Facebook

    YouTube

    YouTube

    Instagram

    Instagram

    LinkedIn

    LinkedIn

    Whatsapp

    +8618926041961

    Email

    sales@oyii.net